How to Hang Rope Lights on a Wall Without Nails  

Rope lights are a great option if you’re looking for a quick, easy, and affordable way to add some extra decorative lighting to your home. You can hang them on the wall without using any nails or screws.

How-to-Hang-Rope-Lights-on-a-Wall-Without-Nails

This blog post will discuss how to hang rope lights on a wall without nails . First, measure the desired location of your rope light on the wall and mark it with tape.

Ensure that there is enough space between the marks to spread the light out evenly. Next, use a stud finder to locate the studs in the wall and make marks where they are.

Then, take a hammer and nails or screws and attach the holder (or holders) for the ropes lights to the wall where the marks are. Be sure to use anchors if you’re attaching them to drywall. Read on to know more!

12 Easy Ways on How to Hang Rope Lights on a Wall Without Nails:

1. Using Adhesive Tape:

Adhesive tape is one way of hanging rope lights on a wall. It has several benefits such as it is easy to buy and comes in many different forms, it’s strong and doesn’t require any tools or extra pieces, is cost-effective and can be used for up to 2 years.

However, you must know that once the adhesive tape is applied to the wall, it cannot be removed without ripping off part of the paint. So if you want to take down or change your rope lights, you will have to go through the whole process again.

2. Using Velcro Ties:

Velcro ties are great for people who simply want to hang their lights for a temporary occasion. They are very simple and easy to use and can be found at most home improvement stores.

Using-Velcro-Ties

The negative side of using Velcro ties is that they are not very strong, can easily be cut by thieves, are not cost-effective, and have to be replaced every time you take down your rope lights.

3. Using Brick Clips:

Brick clips are an easy solution to hanging rope lights on a wall. They do not leave any marks or holes, are very cost-effective, and can be used for removing your lights in the future if needed.

However, brick clips are only good for one-time use and will most likely break with the repeated installation of new sets of lights.

4. Using Low-Adhesive Hanging Strips:

Low adhesive hanging strips are one of the best solutions for hanging lights on a wall. They remove cleanly without damaging paint, consist of 2 parts (one with adhesive and one without), cost less than using nails or screws and leave no residue.

Then, when it comes time to take down your lights, you can simply pull them down by hand without having to break the adhesive strip first.

5. Using Cable Clips:

Cable clips are another great solution for hanging lights on walls without nails or screws.

They are much stronger than brick clips and come in different sizes, are cost-effective, easy to use, leave no marks or holes, and can be used multiple times.

6. Using Adhesive Clips and Hooks:

Adhesive hooks and clips are a popular solution to hanging lights. They come in large and small sizes, can be used for many different applications, and do not need additional tools or pieces.

Using-Adhesive-Clips-and-Hooks

Their only downside is that they damage the paint on your wall if you ever want to take them down.

7. Using Plaster Clips:

Plaster clips are small plastic strips that you melt at one end with a lighter to attach your lights. They are very simple, easy to use, and cost-effective. However, they cannot be reused since the heat will most likely melt them.

8. Using a 3M Mounting Strip:

A 3M mounting strip is one of the best solutions for hanging lights on a wall. It can be used multiple times, leaves no residue, is easy to use, and is cost-effective. Furthermore, they do not damage your paint or leave any holes!

9. Using a Wall Anchor:

A wall anchor is also great for hanging lights on a wall. It’s very simple to use and can be found at most home improvement stores.

The only downside is that it damages your paint if you ever want to take down your lights or switch them out for different ones.

10. Using Molding Strips:

Mount small molding strips at an angle with long screws onto which you can attach your rope lights. They’re very simple to use and do not damage your wall.

The downside is that you will have to drill into the wall to mount them, and they cannot be removed without making a huge mess and damaging the paint on your wall!

11. Use Hot Glue Gun:

A hot glue gun is also a good choice for hanging lights. It can be found at most home improvement stores and consists of 2 parts (the glue stick and the gun that heats it).

Use-Hot-Glue-Gun

Hot glue is very strong, leaves no marks or holes, and costs little. However, remember that once you apply it to your wall, there’s no way to remove it without ripping the paint off.

12. Use Transparent Tape:

The solution we chose was to use transparent tape. We decided on this solution because it’s very simple and doesn’t require any tools or pieces.

It leaves no marks, holes, or damage to the paint and can be used for multiple applications. Its only downside is that you will need a large roll of tape, which can be quite expensive.

Some Helpful Tips and Suggestions

1. Sand the surface of the wall before you start. This will give your adhesive more grip, so it stays on longer.

2. Using a laser level is helpful for this project because your rope lights will be evenly spaced across your walls without guessing where to put them next.

If you cannot use a laser level, try to lay your rope lights out first, then you can use the light bulbs themselves to measure where your next light will go.

3. You can control the level of brightness that comes out of your rope light by how close you space them apart on the wall.

The more room there is between each rope light, the brighter they will shine; but the fewer rooms you use, the more of a glow they will give off and create.

4. It’s easier if you start at one corner and work your way down to ensure that none of your rope lights are crooked or crooked with the wall.

5. Make sure that when you stick your adhesive strips, you press them firmly on the wall, so the adhesive has more grip. Then, when you release, pull your hand away fast so that it doesn’t accidentally unstuck the strip.

6. If you cannot perform any of these steps or do not wish to hang your rope lights on a wall, you can always tie them up using a string with some zigzag knots. That way, they will be more holiday-themed!

7. If you are looking for a different way to your lights, you can also buy some rope lights on an attached roll. You won’t have to worry about putting them on your wall or tying them up.

Why Should You Hang Rope Lights on a Wall?

Rope lights look great anywhere. The glowing lights are versatile and can be used indoors and outdoors, around homes or businesses.

Why-Should-You-Hang-Rope-Lights-on-a-Wall

They’re a wonderful accent to highlight trees or other plants during the summer months, but they also work well as a practical lighting solution for a backyard party or an event space.

Hanging rope lights on a wall is a cheap and easy way to add lights inside or out. Rope lights come in many different lengths, and you can link them together.

So you don’t have to give up a lot of space to create a fantastic glowing light display that will make your home or business stand out.

Common Mistakes to Avoid When Hanging Rope Lights on a Wall

1. Using too few or not enough lights to cover an area

2. Hanging the rope light along one side of a wall, leaving an obvious gap in the lighting effect on the other side.

3. Cutting and duct-taping excess wire in place instead of tidily routing and securing it with clips.

4. Space lights too close together, resulting in a spotty illumination line.

5. Use nails or staple guns to attach the rope light.

6. Failing to secure the rope light firmly enough.

7. Not using sufficient mounting clips, the rope lights drooping over time (and possibly pulling loose).

Rope Lights and Wall Safety:

We should mention that nailing or screwing into a stud is generally considered safe, and we recommend precautions when choosing where to hang anything with electricity, especially in areas like bathrooms and hallways.

Rope-Lights-and-Wall-Safety

However, if you are determined to hang rope lights on your wall, carefully check the following areas for studs before you drill into your wall.

1. First, look at the back of the light piece where the power cord is attached. There should be a small label that describes whether or not there’s a power cord and, if so, how it should be hung.

If you can’t read it clearly or if there’s no label, check the box that came with the light set instead, which should have this information.

2. Second, if your rope lights are hard-wired into an existing power source, look to where the wire attaches to the piece because most of these systems will have a standard power outlet.

3. Finally, if your lights are battery-powered or plugged in with a standard cord, you’ll have a volume knob on the light strand that shows power.

This is often useful when installed outdoors because you can turn it down while not in use to prevent the weather from draining the batteries too quickly.

How Do You Hang Rope Lights Without Damaging Walls?

Without holes in your walls, it’s hard to hang anything on them. Rope lights may seem like a good option for home decoration, but they can leave unwanted marks and holes if you don’t know how to install them properly.

While there are other hanging rope lights without nails or staples, this method uses zip ties and velcro strips.

Zip ties are plastic strips with teeth on one end that can be closed with a zip tool to tighten them around almost any material or substance, including rope lights and walls.

Velcro strips have the same idea as zip ties, but instead of being tightened by a tool, they stick together naturally when rubbed against each other.

The velcro strips can be stuck on the wall and to the rope light so they line up properly, but also peel apart with ease for when you need to take down or move your lights.

If you want to know more about how to hang rope lights on a wall without nails then consider reading this full blog post.

Final Thoughts

Hanging rope lights on a wall without nails can be done in simple steps. All you need is some Command Hooks and wire clothes hangers.

First, find the studs on your wall and mark them with a pencil. Then, use the hooks to attach the clothes hangers to the wall at each marked spot.

Hang the rope lights on the hangers, ensure they are taut against the wall, and enjoy your new light display!

We hope this blog post has been helpful in guiding you on how to hang rope lights on a wall without nails. If you have any questions or want to know more, then feel free to comment below!

Leave a Comment