How to Open Coleman Lantern Battery Pack

If you have a Coleman lantern, then you’ll need to open the battery pack at some point. This can be a little tricky, but with a little instruction, it’s not too difficult.

How-to-Open-Coleman-Lantern-Battery-Pack

In this post, we will guide you on how to open coleman lantern battery pack. First, find the seam on the side of the battery pack and pry it open using a small screwdriver or knife.

Once it’s open, you should be able to see the batteries inside. Carefully remove them and replace them with new ones if needed.

Be sure to close up the battery pack afterward; your lantern will be as good as new! The process should take less than five minutes, and you’ll be able to get replacement batteries for your lantern in no time. Read on for more information.

When Should You Open Coleman Lantern Battery Pack?

It would help if you opened the battery pack when you need to replace the batteries. Over time, the batteries will lose their charge and be unable to power the lantern.

If you find that your lantern isn’t working as well as it used to, it’s probably time to replace the batteries. You’ll know for sure when you open up the pack and find that the batteries are dead. If you find out your batteries are dead, don’t worry. It’s an easy fix.

All you need to do is open up the pack and replace the batteries. Coleman lanterns are a great way to light up your campsite. But like all battery-powered devices, they eventually need new batteries.

Fortunately, opening up the battery pack and replacing the batteries is easy. So if your lantern isn’t working as well as it used to, don’t hesitate to open up the pack and replace the batteries. Your lantern will be good as new in no time!

Step by Step Instructions: How to Open Coleman Lantern Battery Pack

Step 1: Locate the Battery Compartment.

The first step is to locate the battery compartment on your lantern. This is usually located on the bottom of the lantern.

Locate-the-Battery-Compartment

Next, check if there is any screw or latch that is holding the battery compartment closed. The battery compartment might be sealed with a sticker if the lantern is new.

Step 2: Unscrew the Battery Cover.

If there is a screw holding the battery cover in place, use a Phillips head screwdriver to unscrew it. If the lantern is new and the battery compartment is sealed with a sticker, carefully peel back the sticker. And then, set the cover aside.

Step 3: Open the Battery Compartment Carefully.

Now that the battery cover is off, you should be able to see the batteries inside the lantern. Be careful when handling the lantern so that you don’t drop or shake it too much.

This could cause the batteries to come loose from their contact points and create a short circuit. When you open the battery compartment, you will see the battery is wired with two different colors. One is positive (+), and the other is negative (-).

Step 4: Carefully Dettach the Wires.

Using a pair of needle-nose pliers, carefully dettach the wires from the batteries. Try not to touch the metal parts of the batteries with your fingers because this could cause a static discharge that could damage the lantern. Also, ensure that you keep track of which wire is which to reattach them correctly.

Step 5: Remove the Batteries from the Lantern.

Once the wires are detached, you can remove the batteries from the lantern. Be careful not to drop or shake the lantern while doing this. Also, make sure that you keep track of which battery is which to put them back in the correct order.

Remove-the-Batteries-from-the-Lantern

Step 6: Replace the Batteries.

You can now replace your old battery with a new one. First, make sure that you put the batteries in the correct order and attach the wires to the correct terminals.

Then, connect the wires where the positive (+) wire is connected to the positive terminal, and the negative (-) wire is connected to the negative terminal.

Step 7: Close the Battery Compartment.

Once you have replaced the batteries, you can close the battery compartment. If there was a screw holding the cover in place, screw it back in.

If the lantern was new and the compartment was sealed with a sticker, carefully peel back the sticker and press it back in place.

Step 8: Test the Lantern.

Now that you have replaced the batteries, you can test the lantern to see if it is working properly. First, press the power button to turn on the lantern.

Test-the-Lantern

If the lantern doesn’t turn on, ensure the batteries are installed correctly, and the wires are connected to the correct terminals.

Some Helpful Tips and Suggestions:

1. Always handle the lantern carefully to avoid dropping or shaking it. This could damage the batteries or cause them to come loose from their contact points.

2. When you open the battery compartment, note which wire is which so that you can reattach them correctly.

3. Make sure you put the batteries correctly when you close up the compartment. The order is usually marked on the inside of the compartment lid.

4. If you are not using the lantern for an extended period, it is a good idea to remove the batteries and store them in a cool, dry place.

5. Always ensure the O-ring seal is properly seated before you close the battery compartment. This will help to keep moisture and dirt out of the lantern.

How Often Should You Change The Batteries?

You should change the batteries in your Coleman lantern at least once a year and more often if you use it regularly. So if you notice the light dimming or flickering, it’s time to change the batteries.

How-Often-Should-You-Change-The-Batteries

Coleman lantern batteries are easy to find and inexpensive, so there’s no excuse not to keep fresh batteries on hand. To open the battery pack, unscrew the knob at the top of the lantern.

This will loosen the cover and allow you to access the batteries. Remove the old batteries and insert new ones, being careful to observe the correct polarity. Replace the cover and screw it back on tightly.

Your lantern is now ready to use. With fresh batteries, you can be sure that your Coleman lantern will provide dependable light when you need it most. Be sure to keep a few extras on hand, so you’re never caught in the dark.

Final Thoughts

Coleman is a well-known brand when it comes to camping gear and supplies. One of their most popular products is the lantern. The lantern is a portable light source that is powered by batteries.

It is perfect for camping trips, night fishing, or for use around the house during a power outage. The lantern has a battery compartment that houses the batteries that power the light.

Over time, the batteries will need to be replaced. This process is simple and only takes a few minutes to do. Follow the steps below to learn how to open Coleman lantern battery pack and replace the batteries.

We hope this guide is helpful and that you find it easy to follow. If you have any questions about the process, feel free to ask us in the comments below.

Leave a Comment