How to Change Light Bulb in Sub Zero 650 Fridge

If you are the Sub Zero 650 refrigerator owner, then you know that it is a luxurious appliance. However, with great luxury comes great responsibility- including changing light bulbs.

How-to-Change-Light-Bulb-in-Sub-Zero-650-Fridge

Changing a light bulb in your Sub Zero 650 fridge is a process that can seem daunting at first, but with a little guidance, it can be done relatively easily.

In this post, we will walk you through the process step-by-step on how to change light bulb in sub zero 650 fridge, so that you can change the light bulb in your fridge with confidence.

Be sure to unplug the refrigerator before starting this project. You will need a Phillips head screwdriver and a replacement light bulb. Let’s get started!

Step by Step Procedure: How to Change Light Bulb in Sub Zero 650 Fridge

Step 1: Remove Any Top-Shelf Item.

Before starting the project, it is important to clear any items off your fridge’s top-shelf. This will give you more room to work and make the process easier. It will also give you more accessibility when changing the light bulb.

Step 2: Find the Light Diffuser.

The light diffuser is located on the fridge’s ceiling, towards the back. It will be a small plastic casing that houses the light bulb.

Find-the-Light-Diffuser

You will need to unscrew the diffuser to get to the light bulb. But before that, locate the small, white tab on the diffuser. This tab needs to be pushed for the diffuser to come off.

Step 3: Lightly Push the Tab To the Left.

Once you have located the tab, use your finger to push it slightly to the left. You should hear a clicking noise, meaning the diffuser is now released. While doing this, be careful not to drop the diffuser.

Step 4: Pull Down the Brackets.

Now that the diffuser is released, you can pull down on the two brackets holding it in place. These brackets are located on either side of the diffuser. As you pull down on the brackets, it will be easier for you to remove the diffuser.

Step 5: Remove the Diffuser.

With the brackets pulled down, you can now remove the diffuser from the fridge. Again, be careful not to drop it as you remove it.

Set the diffuser aside somewhere safe. Make sure you do not lose the small, white tab! You will need this when it comes time to screw the diffuser back into place.

Step 6: Find and Unscrew the Light Bulb.

The light bulb is located inside the diffuser. Once you have removed the diffuser, you should be able to see the light bulb. It is important to note that the light bulb in your fridge is not a regular household light bulb.

Find-and-Unscrew-the-Light-Bulb

Instead, it is a unique, Sub Zero light bulb found at most hardware stores. Once you have located the light bulb, use your Phillips head screwdriver to unscrew it from the diffuser. Be careful when doing this, as you do not want to drop and break the light bulb.

Step 7: Insert Your New Light Bulb.

Now that the old light bulb has been removed, you can insert the new light bulb into the diffuser. Again, be careful when doing this, as you do not want to drop and break the new light bulb. Once the new light bulb is in place, use your Phillips head screwdriver to screw it into the diffuser.

Step 8: Put the Diffuser Back Into Place.

Now that the new light bulb is in place, you can put the diffuser back into its rightful place. First, take the small white tab and insert it back into the diffuser. Next, line up the two brackets on either side of the diffuser and push them back into place.

Once the brackets are in place, you can screw the diffuser back into the fridge’s ceiling. Be sure not to over-tighten the screws, as this could damage the diffuser.

Step 9: Test The Light Bulb.

Now that you have successfully changed the light bulb in your fridge, it is time to test it out. First, plug your fridge back in and open the door.

The new light bulb should turn on automatically. If it does not, double-check to ensure that the diffuser is screwed in properly and that the new light bulb is screwed in properly.

Step 10: Put Everything Back Into Place.

If the light bulb works properly, you can begin putting everything back into place. Start by putting the items back onto the top shelf of the fridge. Make sure that these items are not blocking the light diffuser.

Put-Everything-Back-Into-Place

When putting items back onto the shelves, be sure not to put them too close to the light diffuser, as this could cause the light bulb to overheat and break. Once all the items are back in the fridge, close the door and enjoy your newly lit fridge!

Additional Tips and Advice:

1. Be sure to use a Sub Zero light bulb when changing the light bulb in your fridge. These bulbs can be found at most hardware stores.

2. Be careful when handling the diffuser and the light bulb. Both of these items are fragile and can easily be broken.

3. If the light bulb does not turn on after changing it, check the fuse box to see if a fuse has blown.

4. Always keep your light bulb clean. A dirty light bulb can cause the fridge to overheat and damage the unit.

5. Always turn off the fridge when changing the light bulb. This will prevent any accidents from happening.

6. Ensure the diffuser is properly secured before turning the fridge back on.

7. If the light bulb still does not work, contact a Sub Zero service technician for assistance.

Choosing Light Bulb For Sub Zero 650 Fridge:

When choosing a light bulb for your Sub Zero 650 fridge, there are a few things you need to consider. The type of light bulb you choose will depend on the wattage and voltage of your fridge, as well as the size of the light fixture.

Choosing-Light-Bulb-For-Sub-Zero-Fridge

You’ll also want to consider the light bulb’s color temperature, as this can affect the look of your food. Most Sub zero refrigerator needs T8 or T12-type fluorescent bulbs with a medium bi-pin (G13) base and an initial lumen output of 1,200 – 2,000 lumens.

The lighting in your fridge should be bright enough to see what’s inside easily, but not so bright that it hurts your eyes. You’ll also want to ensure that the light bulb you choose is the right size for your fridge.

Frequently Asked Questions(FAQ):

Sub-Zero refrigerator models 650 and 690 have an interior light located in the center of the roof. First, remove the power supply to the refrigerator to change the light by unplugging it from the wall outlet or flipping the circuit breaker.

Next, use a Phillips screwdriver to remove the two screws holding the lens cover. Under the cover, you will see the light bulb.

Remove the old bulb and replace it with a new one of the same type. Finally, screw the lens cover back and restore the refrigerator’s power.

There are a few reasons why the light in your Subzero refrigerator might be off. First, make sure that the power is turned on to the unit.

The light will not come on if the power is off, even if the door is open. Next, check to see if the light bulb needs to be replaced. If the light bulb is burned out, it will need to be replaced to get the light back on.

Finally, if none of these solutions work, you may need to call a Subzero appliance repair technician to come and take a look at your unit.

Final Words

Changing a light bulb in a Sub Zero 650 Fridge is straightforward, but it is important to follow them precisely to avoid injury or damage to the fridge. In this post, we have walked you through the process of how to change light bulb in sub zero 650 fridge.

The first step is to remove the grill at the top of the fridge. This can be done by inserting a screwdriver into the two slots on either side and prying it off.

Be careful not to damage the grill, as it is fragile. Once the grill has been removed, you will see four screws holding the light cover. Remove these screws and set them aside.

The light cover should now be free. Pull it down and away from the fridge, careful not to damage the wires. We hope this guide was helpful to you. If you have any questions, please feel free to comment below. Thanks for reading!

Leave a Comment